NICE interior !!! You did a great job !!
Very clean !

Nice Job!

:)

Got a little work done today by "de-modding" the car a bit. Trying to take as much advantage as this unseasonable weather we have been having in Nebraska lately!

Ditched the "C&L" Inlet pipe/mass air meter and "K&N" open filter's on the cold air intake and breather.

Installed a stock mass air meter, air box/tube, oil filler cap, distributor cover, and fan shroud as it was missing one when I got the car.

http://i201.photobucket.com/albums/a...1-17-14031.jpg

http://i201.photobucket.com/albums/a...1-17-14033.jpg

As you can imagine the car runs/drives night and day difference for the BETTER from before with the stock stuff re-installed.

I still need to install..

-Ignition coil cover
-Replace the coolant over flow tank cap
-Remove the "BBK" headers install stock ones
-Install a "Motorcraft" battery
- Clean up the engine compartment.

Looking so much better!! ;)

Absolutely agree! :yes:

Been really busy digging into the car more and fixing some stuff lately

Got the BBK headers removed
http://i201.photobucket.com/albums/a...1-25-14023.jpg

Got the antenna cleaned up and installed
http://i201.photobucket.com/albums/a...1-25-14039.jpg

Got those whatever style of non factory 5.0 badges removed and was intending on putting the original style ones back on, but had these "Black" original style ones laying around and decided to go with them as I believe the will compliment the soon to be black powder coated stock wheels
http://i201.photobucket.com/albums/a...1-25-14037.jpg

Also removed the front splash shields to see how everything looked and found these numbers on the body

Driver side
http://i201.photobucket.com/albums/a...1-25-14028.jpg

Passenger side
http://i201.photobucket.com/albums/a...1-25-14027.jpg

Also was in the middle of replacing the noisy "throw out" bearing and was very pleased to see how unbelievably clean rust wise this car is underneath for it having 172,xxx miles and a Utah car all its life!

Here in Nebraska we are used to cars rusting a soon as they leave the lot :thumbsdown:

But this hope to be $15 throw bearing replacement turned into a $200 dollar part job...here are some findings

Transmission dropped.
http://i201.photobucket.com/albums/a...1-25-14025.jpg

It was very difficult to get the transmission out once I had it unbolted from the bell housing as the bearing had unfortunately eaten into the transmission bearing retainer sleeve
http://i201.photobucket.com/albums/a...1-25-14030.jpg

http://i201.photobucket.com/albums/a...1-25-14032.jpg

Also the little clip/fork that clips on to the pivot ball was bent
http://i201.photobucket.com/albums/a...1-25-14031.jpg

Surprised that the speedometer still worked
http://i201.photobucket.com/albums/a...1-25-14035.jpg

And my last finding as the starter cable looks like something had gotten to it and one of the wires was just lying exposed against the body
http://i201.photobucket.com/albums/a...1-25-14033.jpg

Time to get some new parts coming and hopefully more work done!

New 6piece headlights and front bumper cover back on!

http://i201.photobucket.com/albums/a...1-27-14027.jpg

Parts for the transmission should be here Wednesday! Then I will put the license plate bracket and new all white hood on as soon as I get the transmission back in the car! :)

Man..... I am wore out just reading all of the work you are doing to that car in such a short time LOL
When you are done there, I'll fly you out here to clean the engine compartment on my car !!

lol

:2thumbs: I'm trying to waste no time at all so I can have her ready to drive in the spring time :yes: Plus I love working on these cars and love to do just about anything to help the fox body's and their community...so I just might be on that plane soon! haha!

I agree with John! Love to see all the progress in such a short time! Great job!! ;)

Thanks!!:)

I will report back soon with more progress! :thumbsup: